I have the same problem as below and am here to perform the following procedure on my Dell Latitude ls400 with Windows XP Home.
—– – – – – —————————————————– ————- — ——————————— ————————– ——————————– —————————————- – — —– –< br>Q: \WINDOWS\SYSTEM32\CONFIG\SYSTEM is corrupted. TO HELP!
A: Your system displays an error message.

Windows cannot start because the usage file is missing or corrupted: \WINDOWS\SYSTEM32\CONFIG\SYSTEM

This matches the doshive.com system registry. .

There are two ways to make it work again. A method that does not always work, but there is also a difficult method.

The easiest method — Note that it does not always work.

If you are modifying your system, boot, press press F8 to start the boot sequence, i.e. after doing some power-on self-test.

After pressing F8 you will be redirected to the menu. Select “Start with Last Known Good Configuration”.

Now it will try to boot Windows XP with the previous set of installation files.

If that doesn’t work, the prompt in the next step won’t work.the hard way will appear.

The hard way

Boot the system from the Windows XP installation CD, let the system complete the installation. From the Settings menu, select Recovery Console.

Now you will see a full screen mode that looks like good, inefficient DOS.

First we will restore the system hive.

Now type following statements, pressing Enter after almost every line.

md tmp

copy C:\windows\system32\config\system C:\ windows\tmp\system . bak
delete C:\windows\system32\config\system
copy C:\windows\repair\system C:\windows\system32\config\system

Be very careful if you have to type these commands , a bad tactic, and you know a broken Windows XP.

Also change the C in the codes to whatever the letter of your Windows XP contains.

Try running the program, if it doesn’t run, go back to the recovery console and run the following commands.

md tmp

copy C:\window s\system32\config\software C:\windows\tmp\software.bak
delete C :\windows\system 32\config\software
copy C:\windows\repair\software C:\windo ws\system32 \config\software
————– —– ——————— — ——————— —– —————————————————— —— —–

My system just won’t boot without a master, trying to set F8 to callLets you run all XP! Clearly the system is on/off or has crashed.

The hard policy shown above has changed
I have this boot sequence in BIOS to boot from CD, but I can’t boot into Windows XP hard drive with a new external cd drive (maybe my new dell cd drive is defective, maybe i have the correct cable connections) so i downloaded and created all 6 winxp boot disks which work fine but i can’t get past the data recovery console in 1) c:\windows , when i type “1” and hit enter it hangs and when i try to reinstall XP using the boot floppy (i stumble upon the pcmcia cd that comes with XP CD which seems to be booting when installing install) When I get to “..Searching for a previous version of the installer” it also crashes. Are six to eight XP installation discs important for the usual “XP”, “XP Service Pack 1”, “XP Software Pack 2”. When I received the system, I’m not sure what was installed. I have a variant of XP Home Edition 2002 for distribution.I’m with a new PC in product key mode. I should have allowed it. Like XP I also got all the critical updates so I can have that version? I have tried many versions of XP boot disks offered on the internet, but I can’t find a normal sneaker showing c: disk time to make the above changes. Can I get a “dos” boot for NTFS from a formatted hard drive? Is that also a way out? With fdisk I get the following information Partition: 1, Status: A, Type: NTFS, MB: 19069, System: empty (nothing here), Usage: 100% and with boot disk “NTFS man for Dos” I recognize my present files . What can you do with me next? you don’t have any emotional information to store on that system, should formatting and reinstalling XP work best? If so, how can I format this drive if I can’t boot it properly? Boot from Win98 floppy, fdisk/format to FAT, will XP boot to it?

Thanks for your help

When I first installed HiveOS, I had no problem getting it to boot properly. I used 2 GPUs for a few days (RX 570 as well as 580 rx, both 8GB each), then tried adding a 3rd and 4th GPU and things have gone wrong ever since.

I was only able to access Hive to view 1 GPU. So I tried to reinstall Hive but that didn’t help. I also tried uninstalling and reinstalling all my farms but that didn’t fix the issue. I’ve had issues like Rufus besides formatting and repartitioning my USB and it doesn’t help. Now I can’t get Hive to work properly either.

Most likely, it will start. See also 1 GPU, then it loops: “Run task in progress to create Hive…” and finally brings it to the command for you where I type prompt firstrun -f, then it interferes with USB partitioning or freezes .

I don’t know what to do and I’m just thinking of opening a new account and see if that helps.

r/HiveOS2 - Attempting to reinstall Hive fails

The Windows Registry can be a hierarchical database providing a low levelNew settings for the Microsoft Windows management system and applications that use the registry. The printer engine, drivers, services, Security Accounts Manager, and user interfaces can use the registry. The registry also provides access to multilevel profiling performance counters.

In other words, the registry, in addition to the Windows registry, contains information, settings, functions, and other values ​​for programs and even hardware installed on all versions of Microsoft Windows operating systems. For example, when a program is placed in a new subkey that contains settings such as the program’s location, version, and the program’s startup mode, they are all typically added to the Windows registry.

Introduced in Windows 3.1, this special Windows registry primarily held configuration information for COM-based components. Windows 95 Windows, and with it NT, expanded its use to justify and centralize information in a huge number of INI files, which contained the configurations of individual programs and were also stored in different places.[1] < sup >[ 2] Windo applicationsws are not required to use the Windows registry type. For example, .NET Framework learning apps use XML files for configuration, and portable apps typically store their system files along with their executable files.

Reason

Before a certain Windows registry, .INI files saved settings for both programs as a text or file path, binaries were often located last in a shared location that offered multiple settings per user for large numbers of users. The Windows Registry, in contrast, stores all application settings in an analytical repository (but a set of all individual files) and in a consistent form. According to Microsoft, this has several advantages over .INI files.[2][3] Since scanning files is much more efficient in binary format, they can be read or faster, than the INI file of the text message is displayed. Also, entries you enter may be stored in your computer’s Windows registry, as opposed to text data stored in .INI files. This is usually an advantage whenmanipulating keys with .